Thank you very much for buying this CAmodel SRL Kit, Argentinian company that took advanced technology to its factory for the exclusive design models manufacturing, easy building and excellent flying qualities. We hope you enjoy building and flying this model, anything you need we'll be there to help you and guide you in the building steps and flying, so don't doubt in asking through email or telephone call.

LEGAL ADVISE: This kit is not a toy. Take acknoledge that once it's built it could - in case of fail or bad use - cause serious injury and/or deth to people or animals, also bad damage to third person properties. Place special attention and safe behaviur, not flying outside the flying field limits, not even over houses or people, and also near high tension electrified lines.

CAmodel SRL doesn't take responsability for the use of this model and the facts that it may cause because CAmodel SRL didn't participate of the model's installation.

WARRANTY: CAMODEL S.R.L. gives warranty for this model to the original customer, against manufacturing failures, for the term of 90 days since purchase date. If at the time you receive this model you find any damaged part, you must tell inmediatly to Camodel SRL who will soon work out your claim.

DESCRIPTION:
The Zafiro is an aerobatic model capable of the most audacious 3 D maneuvers or, with reduced control throws, a sport flying with superb performance.
Designed by Marcelo Colombo, it’s easy of construction, from selected laser-cut woods, CNC machined foam parts (factory sheeted with balsa), with a high performance wing profile, makes it a magnific project for pilots who want to begin with 3D flying or for those who want to improve their 3D flying skills.

CHARACTERISTICS:
FUSELAGE LENGHT: 66" = 1680mm
WINGSPAN: 62.5" - 1590mm
WEIGHT: 7.16 lbs - 7.70 lbs = 3250/3500grs
ENGINE: GLOW : 60/90 2C - 91/110 4C
ELECTRIC: HACKER C50 acro

GENERAL INSTRUCTIONS

We recommend that you carefully read this manual and instructions before starting to build the model and that you become familiar with the sequence of construction and the different parts that conform the airplane, according to the ilustrations and photographs that we have provided.

All the parts on the sheet wood are laser cut. They are very easy to remove by cutting the micro-joints that retain them. Do not try to pop them out but instead, cut each micro-joint until the part falls free. In very few cases the laser may not have cut all the way through. Simply free the part by cutting over the line with a razor or an X-Acto knife.

Lightly scrape the surfaces that are mated (to be glued) with a razor or fine sandpaper to remove the charred dust.
Cover the working table with a film or other material to avoid the pieces to stick to it.

LIST OF REQUIRED CONSTRUCTION MATERIALS:
Thin and medium Cianoacrilate
30 minute Epoxi
White glue (aliphatic or vynil)
Hobby knife with #11 blade
Ruler
Hobby planer
Sandpaper in 150, 240 and 400 grit
Masking tape
Sand or pellet filled bags
“C” clamps
# 64 rubber bands
Wooden tongue depressors or similar (for hanging the model during construction)

PARTS LISTING:

LIGHT PLY SHEET NBR. 1, CONTAINING:
F1 firewall
F1B Firewall reinforcement
F2 Landing gear and fuel tank support
F3 Landing gear support
F4 Landing gear reinforcement
F5 Servo plate support and receiver and
battery pack support
F6 Rudder servo plate support
F9 Tail wheel support

BALSA SHEET NBR. 1, CONTAINING:
Wing tip (2)
Stab tip (2)
Wing chord (2)
Tail reinforcement (1)

MISCELLANEOUS WOOD
Pre formed 700x35 mm balsa (4) leading and trailing edges of hinged sections for wing
Pre formed 600x30 mm balsa (2) leading and trailing edges of hinged sections for stab
Stick 500x25 mm balsa (1) leading and trailing edges of hinged sections for rudder
Balsa sheet, 2mm for servo box, elevator and aileron caps
Balsa sheet, 4mm for wing and stab tips
Pre-formed balsa block – top of fin and rudder
Balsa covered foam stabilizer/elevators
Balsa covered foam fin/rudder
Balsa covered foam wing/ailerons
Balsa wood, 20x10x900mm (2)– wing leading edges
Balsa wood, 20x10x900mm (1)– stab leading edges
Dowel, 12mm, for control horn attachment

REQUIRED HARDWARE AND MATERIAL

Engine, YS. 110 OS 91FX or similar.
Or Electric Hacker C50 acro
Propeller, to suit engine
YS 110: 15x8, 15x10, 16x10
OS 91FX: 14x8, 15x7
Hacker C50: APC-E 18x10, 19x10
Spinner 2 ½” (63mm)
Motor mount, w/screws and blind nuts
Radio, 4 channels w/5 servos (minimum 60oz-in torque (6kg/cm)
Covering material (Monokote, Oracover, etc) 3 rolls
Wheels 2 1/2” (65mm)
Wheel axles and collars
Tailwheel bracket w/1” (25mm) wheel
Fuel tank 16-20 oz. (360/480 ccm) or battery pack (electric engine)
Speed control (in case electric engine)
Silicone fuel tubing
Push pull cables and fittings for rudder
Push pull cables and fittings for elevator
Alternative: Kato dual bell crank
Control horns
Clevis
CA hinges
Pushrods
Foam latex for wrapping rx, batt and fuel tank
Screws and nylon insert nuts for landing gear
Nylon screws (1/4”-20W) for wing hold.